Filters
Ducting Fittings
94 products
New to ducting? Read our guide: What is Ducting? Types, Sizes & Materials Explained.
Ducting fittings — the bends, connectors, adaptors, tee pieces, and reducers you need to complete a ventilation duct run. We stock the full Domus range covering both round and rectangular systems: 100mm, 125mm, and 150mm rigid round PVC, plus 110mm x 54mm and 204mm x 60mm flat channel — along with round-to-rectangular adaptors for transitioning between the two. All push-fit, all compatible with the Domus EasiPipe and flat channel ducting we stock. Next-day delivery on all items.
Bends / Connectors / Adaptors / Tee Pieces
What ducting fittings do I need for a standard installation?
At minimum: a straight connector to join duct lengths, at least one bend (90° or 45°) to change direction, and an adaptor to connect the duct to your fan or external grille. For a kitchen cooker hood running through a ceiling void, a typical list would include a round-to-rectangular adaptor (if using flat channel above the cabinets), one or two flat bends, a straight connector, a rectangular-to-round adaptor to transition back, and a wall plate or external grille. Buy one or two spare straight connectors. You'll almost certainly cut a duct length and need to rejoin it.
Are round and rectangular fittings interchangeable?
No, round fittings only fit round duct, and rectangular fittings only fit the matching rectangular size. A 100mm round bend won't connect to 110x54mm flat channel. To switch between the two systems in the same run, you need a round-to-rectangular adaptor — Domus make these for 100mm to 110x54mm, and 125mm to 204x60mm. Each system's bends, connectors, and tee pieces are dedicated to that size and won't interchange with other sizes either.
Should I use 45-degree or 90-degree bends?
Use 45° bends wherever you can. Two 45° bends create a gentler direction change than a single 90° and produce less airflow resistance, roughly 0.5m equivalent duct length per 45° bend versus 1–1.5m for a 90° bend. For a duct dropping from a ceiling void to a wall grille, two 45° bends are almost always better than one sharp 90°. Use 90° bends only where the space forces a tight right-angle turn. If your duct run has three or more 90° bends, consider whether a different route with fewer direction changes would give better performance.
How do Domus push-fit fittings work?
Domus fittings use a spigot system, the male end of the fitting slides inside the duct or into the female end of the next fitting. No adhesive or solvent welding is needed for a secure mechanical joint. The fit is snug enough to hold during installation, but for best airtightness you should seal every joint with PVC duct tape or mastic sealant. This is especially important on extract systems (where negative pressure draws air through any gap) and essential on MVHR installations where the SAP calculation assumes fully sealed ductwork.
What's a round-to-rectangular adaptor and when do I need one?
A round-to-rectangular adaptor transitions between round duct and flat channel in the same run. You need one whenever you're switching from round to rectangular or vice versa, typically where a round fan spigot connects to flat channel ducting above kitchen cabinets, or where flat channel running through a shallow void transitions back to round for the remainder of the run. Domus make adaptors for 100mm round to 110x54mm flat channel, and 125mm round to 204x60mm flat channel. Always use the correct adaptor — never force-fit or tape mismatched systems together.
Do I need different fittings for MVHR systems?
The fittings themselves are the same Domus push-fit range, but the installation standard is higher. MVHR systems run at higher static pressures than simple extract fans, so every joint must be sealed with mastic — not just taped. Leaky ductwork on an MVHR system wastes the heat recovery you've paid for and will underperform against the SAP calculation. For MVHR, many installers also prefer semi-rigid ducting systems (like Domus Radial) over standard rigid PVC fittings for the branch runs, because the continuous semi-rigid tube has fewer joints to seal. If you're specifying fittings for an MVHR installation, call us on 0161 399 3825 and we'll help you choose the right system.
Filters
